/library/oar/handle/123456789/104242 Sun, 09 Nov 2025 08:53:32 GMT 2025-11-09T08:53:32Z /library/oar/handle/123456789/104426 Title: Innovative power conditioning and interfacing circuitry for various energy harvesting devices Abstract: This research work focuses on the design, implementation, fabrication and characterisation of a novel power conditioning integrated circuit proposed for capturing maximal energy from a wide range of energy devices. The proposed power conditioning circuit has a wide input voltage range and power range and employs a maximum power point tracking circuit to operate the energy harvesting device at maximum power at any operating condition. A direct AC/DC-to-DC converter makes this power conditioning circuit compatible with harvesters generating both AC or DC output voltages without the need of external rectification. Energy storage is provided by means of a high storage capacitor which reduces the down time of the load and stores any excess power being generated by the energy harvester. The final stage of the conditioning circuit is a hysteretic controlled buck converter which generates an adjustable, clean, and constant output voltage as required by the load. Both circuit stages were fabricated while requiring a minimum number of external components. In particular, the work undertaken and explained in this dissertation can be classified into two main parts. The first part focuses on the design, implementation, simulation, fabrication and characterisation of a novel direct AC/DC-to-DC converter with MPPT function. The second part focuses on the design, implementation, simulation, fabrication and characterisation of a novel hysteretic controlled buck converter integrated with on-chip bootstrapping circuit. Description: Ph.D.(Melit.) Sat, 01 Jan 2022 00:00:00 GMT /library/oar/handle/123456789/104426 2022-01-01T00:00:00Z /library/oar/handle/123456789/104369 Title: Front-end readout electronics for the ALICE CPV and HMPID particle detectors Abstract: This work, carried out in collaboration with the European Council for Nuclear Research (CERN) and the University of Malta, presents the development of a new electronic front-end readout system for the High momentum particle identification (HMPID) and Charged Particle Veto (CPV) detectors. The upgrade strategy of the A Large Ion Collider Experiment (ALICE) is based on the collection of more than 10 nb-1 Pb-Pb collisions at a luminosity of 6x1027 cm-2 8 -1, corresponding to a collision rate of 50 kHz for Pb-Pb and 200 kHz for pp and p-Pb. The requirements for such a high beam luminosity cannot be met with the existing CPV electronics, which had a low readout rate of 5 kHz. The development of such a system is a challenging task. Therefore, different technologies and architectural topologies were considered and investigated for the optimization of the front-end readout electronics. This work contributed to the development of a new custom front-end readout electronics system architecture for the CPV detector module in the PHOton spectrometer (PHOS). This newly developed electronics were commissioned and accepted by the Russian Institute of High Energy Physics and the ALICE collaboration for installation in November 2020. Compared to previous systems, the proposed new architecture allows parallel readout and processing of all 480 silicon photomultiplier pads connected to digital signal processing boards. Optimization strategies include the use of 28 nm FPGA technology with high pin count and low power consumption for simultaneous readout of digital signal processors, referred to as 5 DIL boards, and the use of high-speed 3.125 Gbps transceiver interconnects. In addition, the newly developed FPGA firmware architecture has helped increase the event readout rate and data throughput by a factor of ten. This work enables both the CPV and HMPID detectors to achieve an interaction rate of at least 50 kHz. The system design consists of three modules, each containing two segment cards, two readout common boards (RCBs), and 20 digital signal processors. Five processors are grouped on an electronic board called 5- DIL board. This report presents the architectural layout and preliminary results of performance measurements for the proposed new design. In addition, this work has contributed to the development of a new ASIC chip that integrates four digital signal processors, error correction and detection circuitry, and four serial transmitters with a bandwidth of at least 0.5 Gbps. The ASIC chip implementation uses XFAB-180-nm technology and is capable of processing at least 192 analogue channels simultaneously. The developed ASIC device can be easily integrated into current CPV and similar electronic readout circuits for physics particle detectors, which helps reduce the required number of electronic components and PCB manufacturing costs. This work concludes with recommendations for further planned updates to the hardware scheme. Description: Ph.D.(Melit.) Sat, 01 Jan 2022 00:00:00 GMT /library/oar/handle/123456789/104369 2022-01-01T00:00:00Z